Skip to main content

STMicro STM32F10x CMSIS-SVD files appear to be missing lots of important registers

CMSIS-SVD is "Cortex Microcontroller Software Interface Standard" "System View Description". This is an ARM standard format for describing the registers and their bitfields for the Cortex-M series of ARM processors.

If you have an account on the Arm website you can visit the STMicro cmsis page where you can download the svd files for various STMicro processors. The STM32F10x svd files however appear to be missing important things like the system control block.

This is an issue because I've been using the Eclipse plugin EmbSysRegView to browse cpu registers during debug. The system control block is important because it contains various status registers that report fault status. These registers can help to locate issues in code or configuration.

I posted a support question with ST and on their forums to see why their CMSIS-SVD doesn't appear to include all of the processors registers but I'll probably end up modifying the other EmbSysRegView processor definitions, the user submitted ones not the ones from ST, to add the missing entries.



Labels:

Comments

  1. UnknownJanuary 27, 2016 at 5:49 AM

    I'm facing the same problem today. Seems like the situation did not change over time...

    ReplyDelete

Post a Comment

Popular posts from this blog

UTM (qemu on OSX) only boots into uefi shell after installing Ubuntu 22.10 (solved!)

I've been meaning to try out running Linux and Windows virtual machines on my x86 MacBook Pro using qemu . I've been using Parallels for several years. Parallels is a nice application and works well but I'm always getting bugged to purchase upgrades. Parallels provides free updates on minor version upgrades only, say 13.0 to 13.1. With so many prompts to purchase upgrades it feels like Parallels could release a bit more minor versions and a bit fewer major versions. Rather than just purchase an upgrade to Parallels I figured I'd try out qemu via the UTM application . UTM wraps qemu with a helpful gui and comes as a packages Mac application. And UTM supports both x86 and M1 systems (as qemu also supports these systems). Creating an Ubuntu VM with UTM didn't go as smoothly as with VirtualBox or Parallels but it was the settings I chose that messed me up. Here are two things I ran into when installing Ubuntu on UTM. #1. Configure the qemu instance to use a 'Display...
Post a Comment
Read more

Debugging an imprecise bus access fault on a Cortex-M3

This information may apply to other cortex series processors but is written from practical experience with the Cortex-M3. Imprecise bus access faults are ambiguous, as noted by the term "imprecise". Compared to precise bus errors, imprecise errors are much trickier to debug and especially so without a deep understanding of arm processors and assembly language. Imprecise and precise flags are found in the BusFault status register, a byte in the CFSR (Configurable Fault Status Register). BusFault status register bits The definition for imprecise and precise bits is: [2] IMPRECISERR Imprecise data bus error: 0 = no imprecise data bus error 1 = a data bus error has occurred, but the return address in the stack frame is not related to the instruction that caused the error. When the processor sets this bit to 1, it does not write a fault address to the BFAR. This is an asynchronous fault. Therefore, if it is detected when the priority of the current pr...
5 comments
Read more

Graco Swing By Me - Battery to AC wall adapter modification

If you have one of these Graco battery powered swings you are probably familiar with the cost of C batteries! The swing takes four of them and they only last a handful of days. I'm not sure if the newer models support being plugged into the wall but ours didn't. If you are a little familiar with electronics and soldering, here is a rough guide on how you can modify yours to plug in! I wasn't sure how exactly to disassemble the swing side where the batteries were. I was able to open up the clamshell a bit but throughout this mod I was unable to determine how to fully separate the pieces. I suspect that there is some kind of a slip plate on the moving arm portion. The two parts of the plastic are assembled and the moving arm portion with the slip plate is slid onto the shaft. Because of the tension in that slip plate it doesn't want to back away, and because of the mechanicals that portion of the assembly doesn't appear accessible in order to free it. I was...
Post a Comment
Read more